It's the oscillator that is being modulated by changing the reactance to vary the frequency.

You can immediately eliminate two options: an audio amp does not by itself generate FM emissions, and the job of the final amp is to amplify a pre-modulated signal. The answer must be one of the options pertaining to an oscillator, but it’s less obvious which of these two remaining options is correct.

You know that the resonant frequency of a capacitive-inductive (i.g. RLC) oscillator is determined by its inductance and capacitance, so modulating reactance (by modulating inductance or capacitance) is one way to modulate frequency.

A balanced oscillator, on the other hand, is used to generate dual sideband carrier-suppressed signals, not FM. Read more about how this works: https://electronicspost.com/explain-the-generation-of-dsb-sc-signal-with-balanced-modulator-using-diodes/

Hint: My reaction (reactance) is that "modulator" rhymes with "oscillator" thus the answer.

Last edited by kd7bbc. Register to edit

Tags: none

Remember that reactance has to do with inductors and capacitors, not resistors. This eliminates two of the distractors.

Inductance/reactance affect the phase (PM) of a wave, not the amplitude, which eliminates the final distractor.

Be aware that this question is a little misleading in that phase modulation (PM) is not the only use of a reactance modulator. Reactance modulation is also one way to modulate frequency, per the previous question.

Last edited by wileyj2956. Register to edit

Tags: none

FM stands for Frequency Modulation and is a method of sending an audio signal by modulating the frequency of the signal. In order to convert that signal back to regular audio the receiver needs something that can discriminate (or detect) the changes in frequency.

Thus, the circuit that detects the FM signals is called a Frequency Discriminator (or sometimes Frequency Detector).

Hint: "Discriminator" and "Detecting" both start with the letter "D" -KC1OHT

Last edited by kd7bbc. Register to edit

Tags: none

One way a single-sideband phone signal can be generated is by using a balanced modulator followed by a filter.

Balanced Modulator (both side bands) + Filter (filter out 1 side band) = Single Side Band

Two methods of SSB Transmissions

A balanced oscillator produces a dual sideband carrier-suppressed (DSB-CS) signal. Filtering out one of the sidebands results in an SSB signal.

Only one answer has the word "filter" in it.

— mrdfox7

Hint: Think "Single Side Balanced"

— serif

Last edited by serif. Register to edit

Tags: none

Emphasis is the boosting of lower-power frequencies to improve the signal-to-noise ratio.

Typically, higher-frequency components of a signal are "pre-emphasized" before transmission in order to produce a more equal modulation index, and therefore a better signal-to-noise ratio for the entire frequency range.

On reception, the signal is "de-emphasized" to recover the original power distribution.

Source: Wikipedia

Last edited by meetar. Register to edit

Tags: none

De-emphasis means attenuating higher received frequencies by the amount by which they were boosted prior to transmission. The purpose is to improve signal-to-noise ratio.

From: http://www.daenotes.com/electronics/communication-system/pre-emphasis-and-de-emphasis

Phase modulation (PM) inherently emphasizes higher frequencies at 6 dB/octave, requiring PM receivers to de-emphasize the signal upon reception. In the early days of frequency modulation (FM), common PM receivers with in-built de-emphasis were sometimes re-purposed for FM. Artificially adding emphasis to FM signals prior to transmission made PM receivers more easily converted for FM, with the side benefit of substantially improving signal-to-noise ratio for FM.

Hint: Question has "commonly" and "communications".. correct answer is the one that also has a "c" word - "compatibility"

http://www.repeater-builder.com/tech-info/pdemph-post.html

Last edited by ki5hav. Register to edit

Tags: none

Baseband is commonly used to indicate the range (band) of source frequencies used to modulate the transmitted signal.

Generally, a transmission signal contains more than a single frequency. This is to say that there might be several different frequencies linked together or superimposed on each other.

Baseband refers to the original frequency range of a transmission signal before it is converted, or modulated, to a different frequency range. For example, an audio signal may have a Baseband range from 20 to 20,000 hertz. When it is transmitted on a radio frequency (RF), it is modulated to a much higher, inaudible, frequency range. Most telecommunication protocols require original Baseband signals to be modulated to a higher frequency before they are transmitted. These signals are then demodulated at the destination, so the recipient receives the original baseband signal.

Hint: The point prior to modulation

Another Hint: In the question it mentions radio communications so the answer would be the only one with message in it. Communications=message

Last edited by w9mel75. Register to edit

Tags: none

The sum and difference frequencies are the frequencies added together and subtracted apart, i.e 10kHz + 15 kHz will mix to 25kHz and 5kHz

Last edited by waterlubber. Register to edit

Tags: none

Radio Frequency (RF) mixer circuits operate at radio wave frequencies and are designed for some maximum amount of input signal.

Think of what happens when you yell into a microphone on SSB - your voice won't sound louder, it will sound distorted. In this case, the spurious products are in the audio range. This is an example of an excessive amount of signal from the microphone going into an audio amplifier.

In an RF mixer, the effect is to generate mixer products which are not linear representations of the input signal. These are called "spurious mixer products" and can be at audio and RF frequencies.

So, we don't want the maximum amount of RF signal applied to a mixer, because it might exceed the design parameters and could generate spurious mixer products. We want the input to the mixer to be something that won't generate spurious mixer products.

Last edited by k6yxh. Register to edit

Tags: none

A Diode Detector is the simplest way of demodulating AM signals. It operates by detecting the envelope of the incoming signal which it does by rectifying the signal. Current is allowed to flow through the diode in only one direction, giving either the positive or negative half of the envelope at the output.

The AM detector or demodulator includes a capacitor at the output. Its purpose is to remove any radio frequency components of the signal at the output (Read Filtering). The value is chosen so that it does not affect the audio base-band signal.

Source: Radio-electronics.com - Diode detector basics

Hint: Remember Rectification

Memory Tip: Envelopes are RECTangles.

Last edited by w6pen. Register to edit

Tags: none

A product detector mixes the incoming SSB signal with a local oscillator (e.g. BFO) to produce a demodulated audio signal.

How to remember it is both the question and answer have the word detector and you are detecting a product.

Last edited by w6pen. Register to edit

Tags: none