Login or Register for FREE!
Login or Register for FREE!
Subel. ZLG
20 questions
Subelement ZLG
Operating an Amateur Radio Station
Section ZLG24
Practical Operating Knowledge
You are mobile and talking through a VHF repeater. The other station reports that you keep "dropping out". This means
  • your signal is drifting lower in frequency
  • Correct Answer
    your signal does not have enough strength to operate the repeater
  • your voice is too low-pitched to be understood
  • you are not speaking loudly enough
This question does not yet have an explanation! Register to add one

Tags: none

A "pileup" is
  • an old, worn-out radio
  • another name for a junkbox
  • Correct Answer
    a large group of stations all calling the same DX station
  • a type of selenium rectifier
This question does not yet have an explanation! Register to add one

Tags: none

"Break-in keying" means
  • unauthorised entry has resulted in station equipment disappearing
  • temporary emergency operating
  • Correct Answer
    key-down changes the station to transmit, key-up to receive
  • the other station's keying is erratic
This question does not yet have an explanation! Register to add one

Tags: none

A repeater operating with a "positive 600 kHz split"
  • Correct Answer
    listens on a frequency 600 kHz higher than its designated frequency
  • transmits on a frequency 600 kHz higher than its designated frequency
  • transmits simultaneously on its designated frequency and one 600 kHz higher
  • uses positive modulation with a bandwidth of 600 kHz
This question does not yet have an explanation! Register to add one

Tags: none

The standard frequency offset (split) for 2 metre repeaters in New Zealand is
  • Correct Answer
    plus 600 kHz above 147 MHz, minus 600 kHz on or below 147 MHz
  • plus 600 kHz below 147 MHz, minus 600 kHz on or above 147 MHz
  • minus 5 MHz below 147 MHz, plus 5 MHz kHz on or above 147 MHz
  • plus 5 MHz below 147 MHz, minus 5 MHz kHz on or above 147 MHz
This question does not yet have an explanation! Register to add one

Tags: none

The standard frequency offset (split) for 70 cm repeaters in New Zealand is plus or minus
  • 600 kHz
  • 1 MHz
  • 2 MHZ
  • Correct Answer
    5 MHz
This question does not yet have an explanation! Register to add one

Tags: none

You are adjusting an antenna matching unit using an SWR bridge. You should adjust for
  • maximum reflected power
  • equal reflected and transmitted power
  • Correct Answer
    minimum reflected power
  • minimum transmitted power
This question does not yet have an explanation! Register to add one

Tags: none

The "squelch" or "muting" circuitry on a VHF receiver
  • Correct Answer
    inhibits the audio output unless a station is being received
  • compresses incoming voice signals to make them more intelligible
  • reduces audio burst noise due to lightning emissions
  • reduces the noise on incoming signals
This question does not yet have an explanation! Register to add one

Tags: none

The "S meter" on a receiver
  • indicates where the squelch control should be set
  • indicates the standing wave ratio
  • indicates the state of the battery voltage
  • Correct Answer
    indicates relative incoming signal strengths
This question does not yet have an explanation! Register to add one

Tags: none

The "National System" is
  • the legal licensing standard of Amateur operation in New Zealand
  • Correct Answer
    a series of nationwide amateur radio linked repeaters in the 70 cm band
  • the official New Zealand repeater band plan
  • A nationwide emergency communications procedure
This question does not yet have an explanation! Register to add one

Tags: none

A noise blanker on a receiver is most effective to reduce
  • 50 Hz power supply hum
  • noise originating from the mixer stage of the receiver
  • Correct Answer
    ignition noise
  • noise originating from the RF stage of the receiver.
This question does not yet have an explanation! Register to add one

Tags: none

The purpose of a VOX unit in a transceiver is to
  • Correct Answer
    change from receiving to transmitting using the sound of the operator's voice
  • check the transmitting frequency using the voice operated crystal
  • enable a volume operated extension speaker for remote listening
  • enable the variable oscillator crystal
This question does not yet have an explanation! Register to add one

Tags: none

"VOX" stands for
  • volume operated extension speaker
  • Correct Answer
    voice operated transmit
  • variable oscillator transmitter
  • voice operated expander
This question does not yet have an explanation! Register to add one

Tags: none

"RIT" stands for
  • receiver interference transmuter
  • range independent transmission
  • Correct Answer
    receiver incremental tuning
  • random interference tester
This question does not yet have an explanation! Register to add one

Tags: none

The "RIT" control on a transceiver
  • reduces interference on the transmission
  • changes the frequency of the transmitter section without affecting the frequency of the receiver section
  • changes the transmitting and receiver frequencies by the same amount
  • Correct Answer
    changes the frequency of the receiver section without affecting the frequency of the transmitter section

RIT - "Receiver Incremental Tuning". A transceiver is usually a receiver and transmitter combination sharing a lot of common circuits - such as the various oscillators that determine its operating frequency. RIT provides a tuning facility so the receiver can be separately tuned for a few kHz each side of the transmit frequency, hence giving independent control over the receive frequency.

Last edited by cmscouler. Register to edit

Tags: none

The "split frequency" function on a transceiver allows the operator to
  • Correct Answer
    transmit on one frequency and receive on another
  • monitor two frequencies simultaneously using a single loudspeaker
  • monitor two frequencies simultaneously using two loudspeakers
  • receive CW and SSB signals simultaneously on the same frequency
This question does not yet have an explanation! Register to add one

Tags: none

The term "ALC" stands for
  • audio limiter control
  • Correct Answer
    automatic level control
  • automatic loudness control
  • automatic listening control

ALC - "Automatic Level Control". Just as we had AGC in a receiver, this is a similar thing for transmitters, usually for the linear amplifiers used in SSB transmitters. Its purpose is to prevent over-driving the linear amplifier stages especially the final amplifier. It may also permit the peaks of an SSB signal to be limited in amplitude to enable an increase in the mean output power of the transmitter to improve the relative signal level at a distant receiver. This function can also involve processing the audio in the transmitter, known as "compression" .

Last edited by cmscouler. Register to edit

Tags: none

The AGC circuit is to
  • expand the audio gain
  • limit the extent of amplitude generation
  • Correct Answer
    minimise the adjustments needed to the receiver gain control knobs
  • amplitude limit the crystal oscillator output
This question does not yet have an explanation! Register to add one

Tags: none

Many receivers have both RF and AF gain controls. These allow the operator to
  • vary the receiver frequency and AM transmitter frequency independently
  • vary the low and high frequency audio gain independently
  • vary the receiver's "real" and "absolute" frequencies independently
  • Correct Answer
    vary the gain of the radio frequency and audio frequency amplifier stages independently
This question does not yet have an explanation! Register to add one

Tags: none

The term "PTT" means
  • Correct Answer
    push to talk
  • piezo-electric transducer transmitter
  • phase testing terminal
  • phased transmission transponder
This question does not yet have an explanation! Register to add one

Tags: none

Go to ZLG23 Go to ZLG25
HamStudy.org™ is copyright 2024 Signal Stuff™, All rights reserved.
View Privacy Policy    |    Get help with HamStudy.org™